Exploring Basic Plumbing When You Install a Bathtub
Exploring Basic Plumbing When You Install a Bathtub
Blog Article
Are you currently on the lookout for answers about How to Install a Bathtub?
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a new one is also a moderately difficult project. If the old tub is easily easily accessible, the task can move immediately; if you have to open up a wall to eliminate the old tub and also place the brand-new bath tub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will require a helper to leave the old tub and also embeded in the new one. Ensure you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is much better to consider employing one prior to you begin. Possibilities are you may need a professional plumber to make tube connections.
This post will certainly assist you install a brand-new tub in your shower room if you have currently bought a new bathtub and do not need to alter the plan of your previous water supply pipelines.
Your devices and also material checklist should comprise the following:
Planning for the Setup
First of all, the supporting frame provided with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to avoid stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain any type of water staying in the system. The process of removing the existing faucets can be fairly problematic because of the limited gain access to that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipes. When the supply pipelines have been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Before moving on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are practical in equally spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next goal is to ensure that the tub is leveled all round. This can be achieved by examining the level as well as readjusting the feet on the bath tub until the spirit level reads level.
To set up taps, fit all-time low of the furthest flexible tap port to the proper supply pipe by making a compression sign up with; then do the same for the other tap.
Activate the water system and also check all joints and brand-new pipework for leakages and also tighten them if required. Fill up the bathtub and also examine the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the maker's user's manual. Tiling and also sealing around the tub must wait till the bathtub has actually been utilized at least once as this will settle it into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in location in between the faucet and also the sink. Protect the faucet in place with the maker offered backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The former type must be connected to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack a stiff seal, causing the water to penetrate the wall between the bath as well as the tiling, resulting in problems with moisture and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Remember to constantly load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can break relatively early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently offered on the marketplace. It is advisable to fit the tiles making use of waterproof or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our section on A Step-by-Step Guide to Installing a Bathtub. Thank you for taking time to read our posting. Sharing is nice. One never knows, you might be doing someone a favor. Bless you for your time. Kindly visit our blog back soon.
Book Instantly Report this page